風道電加熱器主要用于風道中的空氣加熱規格分為低溫、中溫、高溫三種形式,在結構上的共同之處是采用鋼板支撐電熱管以減少電熱管的振動,接線盒中都裝有超溫控制裝置。
另在控制方面除裝有超溫保護外,還在風機與加熱器之間加裝聯運裝置,以確保電加熱器起動必須在風機起動之后,在加熱器前后加一差壓裝置,以防風機故障,通道加熱器加熱的氣體壓力一般不應超過0.3Kg/cm2,如需超過以上壓力,請選用循環式電加熱器;低溫型加熱器氣體加熱最高溫度不超過160℃;中溫型不超過260℃;高溫型不超過500℃。
風道式電加熱器用于工業風道、空調風道與各行業空氣通過對空氣的加熱,提高輸出空氣的溫度,一般在風道橫向開口插入。根據風道工作溫度分低溫、中溫和高溫;根據風道內風速分低風速、中風速和高風速。
水電加熱器根據安裝形式可分為臥式流體電加熱器和立式流體電加熱器兩種 ,被加熱介質由泵體壓力輸入,水電加熱器在流動過程中吸收熱能達到用戶工藝需求的溫度送到用戶端。
水電加熱器通過出口處的智能溫控裝置和電力調功系統可保證流體介質溫度能滿足 用戶的工藝需求變化,同時借助于設備內部傳感器和各種保護裝置,一旦介質溫度超出設備設定的溫度范圍,智能溫控系統將迅速作出反應,停止加熱運行,并提示 故障報警,以避免加熱設備的損壞。
眾所周知,太陽能發電的最大劣勢在于陽光輻照的間歇性,而太陽落山的時候往往是人們的用電高峰期。因此,全球的太陽能公司都想設計一個可以存貯太陽熱量的系統,使電站能夠在陰天夜晚正常運行。各國技術人員嘗試了各種各樣的設計,但最終只有西班牙的Gemasolar電站成功了,該電站也因此獲得了國際上一系列的獎項。
As everyone knows, the biggest disadvantage lies in the intermittent solar power sunlight irradiation, while the sun is often people's peak electricity. Therefore, the global solar energy companies want to design a storage of solar heat system, so that the power plant can run normally in the cloudy night. Technical personnel in various countries try a variety of designs, but in the end only the Spanish Gemasolar station is successful, the plant has thus received a series of awards in international.
Gemasolar光熱電站位于西班牙塞維利亞市附近,由西班牙Torresol能源公司投資建設,它自帶15小時熔鹽儲熱系統,滿負荷狀態下能夠維持電站穩定運行18個小時以上而不要任何額外的能量,而且一年好幾個月它都能夠每天連續運行24小時。該電站裝機規模僅20MW,能夠滿足25000個家庭日常用電,每年可以減排二氧化碳30000噸。
Gemasolar thermal power plant is located near the Spanish city of Seville, investment and construction by Spain's Torresol energy company, it comes with 15 hours of molten salt heat storage system, which can maintain the plant stable operation for more than 18 hours without any additional energy full load condition, and a year for several months it can run continuously for 24 hours a day. The power station installed capacity is only 20MW, which can meet the 25000 family daily use of electricity, each year 30000 tons of carbon dioxide emissions.
Gemasolar電站使用了2650套定日鏡,共占地185公頃。定日鏡群將太陽能集中到塔式集熱器,集熱器集中的熱量將熔鹽加熱到發電所需要的溫度。滿負荷運轉情況下多余的熱量通過熔鹽存在熔鹽罐中,供陰天或者夜晚使用。
Gemasolar power plant using 2650 sets of heliostat, covers an area of 185 hectares. Heliostat group will be concentrated to the tower solar energy collector, collector concentration in the heat of the molten salt heating to power the required temperature. Full load excess calories running condition by molten salt exists in molten salts, for cloudy days or night use.
憑借Gemasolar電站的成功運行,投資方西班牙Torresol能源公司被授予DESERTEC2014大獎——“Pioneering Design”獎項。DESERTEC是一個致力于通過在沙漠地區建設光熱電站來為歐洲提供電力的組織,他們已經篩選出了4個電站,這些電站的共同點是都能夠把太陽能儲存后用于夜晚發電。他們將Gemasolar電站形容為“未來電站的先驅者”。
With the successful operation of Gemasolar power plant, the investment side of the Spanish energy company Torresol was awarded the -- "Pioneering Design" award at the DESERTEC2014 awards. DESERTEC is a dedicated by desert area in building solar thermal power stations to provide electricity for the organization in Europe, they have identified 4 power plants, common to these power plants are able to store solar energy for power generation after the night. They will be described as "a pioneer of the future Gemasolar power station".
截止目前,Gemasolar電站已經正常運行3年之久了,這說明該電站采用的熔鹽塔式太陽能熱發電技術是成功的。Torresol能源公司和DESERTEC機構都認為全球?qū)?huì)建設更多更大規模類似Gemasolar的電站。
To date, Gemasolar power plant has been running for 3 years, and this shows that the molten salt solar thermal power tower technology of this plant is used in successful. Torresol energy and DESERTEC agencies think global will be more large-scale construction similar to the Gemasolar power station.
據統計,目前全球共建成105座太陽能光熱電站。其中加利福尼亞的SEGS槽式光熱電站已經連續運行了30年,SEGS電站之后美國又在西部沙漠地區建設了一大批光熱電站。作為全球光熱發電技術的領先者,西班牙公司采用熔鹽儲熱技術在中東沙漠地區也建立了大批不同發電形式的光熱電站,而Gemasolar電站被認為是目前建設成功的一個。
According to statistics, at present, the world has built 105 solar thermal power stations. The SEGS groove type solar thermal power stations in California have operated continuously for 30 years, SEGS power after the United States and in the western desert area construction of a large number of power stations. As a global leader in solar thermal power generation technology, Spanish Company in the Middle East desert area has also built a large number of different forms of power generation thermal power station by the molten salt heat storage technology, and Gemasolar power station is now considered to be the most successful one construction.
目前,全球各大光熱發電巨頭都在對熔鹽塔式技術和項目進行研究和部署。美國SolarReserve在建的110MW的塔式熔鹽光熱電站新月沙丘電站正在進行最后階段的調試,即將并網發電。光熱發電巨頭Abengoa也正在智利籌備建設110MW的Cerro Dominador熔鹽塔式光熱電站,該項目也將成為Abengoa應用熔鹽塔式技術的商業化電站。除此之外,Masdar和Sener這兩個投建了Gemasolar項目的公司對熔鹽塔式技術的應用也在進行更多的部署。在中國,首航光熱已經在籌備開工建設10MW的熔鹽塔式電站,中控太陽能在建設完畢10MW的水工質塔式電站后,正加快塔式熔鹽技術的應用步伐。
At present, the global various light heat power generation giants in the molten salt tower technology and project research and deployment. Power station power stations barchan tower molten salt of American SolarReserve in the construction of the installation in the world's largest 110MW are debugging the final stage, the upcoming grid generation. Solar thermal power generation giant Abengoa is also Cerro Dominador molten salt tower solar thermal power stations Chile preparations for the construction of 110MW, the project will also become the first commercial power plant technology application of Abengoa molten salt tower. In addition, Masdar and Sener of the two voted to build Gemasolar project company application of molten salt tower technology are also more deployment. In China, the molten salt tower power plant has been in preparation for the inaugural photothermal started construction of the first 10MW, in the control of solar energy in the water medium tower power plant construction completed 10MW, is accelerating the pace of tower molten salt technology application.
塔式熔鹽技術的優點明顯,但技術難度較槽式和水工質塔式技術都大。但國內外業內目前普遍看好該技術的市場前景,這已成為光熱發電未來發展的主流方向之一。
The advantages of tower molten salt technology is obvious, but the technical difficulty is trough and the water medium large tower technology. But the industry at home and abroad at present generally optimistic about the technology market prospects, it has become one of the main direction of the future development of thermal power generation.
初次采用導熱油加熱系統的用戶,因其沒有調試和使用經驗對導熱油加熱系統的開工調試很茫然,對系統的穩定運行更是胸中無數,新用戶們不必?fù)?dān)心,萬森公司會告知你開工調試關鍵點,也許對你有所幫助。
開工調試關鍵點是烘爐及煮油。
1.烘爐
烘爐的關鍵點是嚴格按廠家提供的烘爐曲線緩慢升溫,控制爐出口油溫在90℃以下,嚴禁采用大火,以免造成爐體開裂。根據經驗一般小型導熱油爐的烘爐時間3~4天;大型6~7天。
2.煮油
常將新導熱油脫出水分及輕組分的過程稱為煮油。煮油的關鍵點是嚴格按廠家提供的升溫曲線緩慢升溫,脫水、排氣要徹底才能保證系統的安全穩定運行。
(1) 脫水階段——油溫95~135℃區間
在導熱油加熱溫度由95℃升至135℃的區間,為緩慢升溫、脫水排氣階段,控制升溫速度在5℃/h以下。當出現排氣量大,泵壓加大,壓力表指針擺動較大,管道振動加速時,必須停止升溫,保持恒溫狀態,必要時可打開爐門減弱燃燒,
待現象減緩,泵出口壓力降至0.1MPa再行升溫。如此反復幾次,才能將水分排凈,直到放空管不再有氣體排出,壓力表指針停止波動即為脫水合格。此時,系統還需再繼續運行2~3h,直至完全穩定。
脫水時間長短視系統含水情況而不同,短則十幾小時,長則數十日。切不可為縮短脫水時間盲目加快升溫過程以免引起“突沸”噴油,造成安全事故。
(2)脫輕組分階段——油溫210~230℃區間
210~230℃的區間為脫出輕組分階段,控制升溫速度10℃/h。脫水過程完成后,以30℃/h升溫速度升至210℃,當溫度升至210℃時,導熱油中所含低沸物即輕組分的揮發,又將出現脫水階段的現象,處理方法同脫水階段。脫輕結束后,系統需繼續運行4小時,至完全穩定。
脫輕組分過程與導熱油的質量有關,不同牌號、不同質量導熱油的脫輕過程不同。
(3)上述脫水及脫輕階段,嚴禁關閉熱油泵。當溫度升至200以上時應對設備和整個系統進行一次全面檢查,查看各連接部位有否泄露,高位槽(膨脹器)是否保持正常液位,各部位螺栓是否有松動等,發現問題及時處理。
熱水器鑄鋁加熱器,專業名稱為:3D MAX集成極速加熱系統,是即熱式電熱水器的核心加熱系統。由獨立的水流通道三維立體環繞于加熱元件周?chē)?,集成環繞水路、核心平面加熱、恒溫控制撒熱裝置、防干燒保護裝置、防水垢設計系統于一體,有效地解決了即熱式加熱系統的漏水、漏電、水垢、干燒及出水溫度忽冷忽熱等安全性能方面問題,更好的提高了效率和速度。 因其加工工藝為鋁合金整體鑄造成形的鑄鋁加熱技術,俗稱“鑄鋁”加熱器。是由獨立的水流通道三維立體環繞于加熱元件周?chē)h(huán)繞水路、核心平面加熱、恒溫控制撒熱裝置、防干燒保護裝置、防水垢設計系統等于一體,有效地解決了即熱式加熱系統的漏水、漏電、水垢、干燒及出水溫度忽冷忽熱等安全性能方面問題,更好的提高了效率和速度。是浙江萬森技術人員通過多年努力結合各種熱水器與即熱式加熱技術之優點而研發出來的集成加熱系統,將即熱式電熱水器加熱技術得到提升和完善。并逐步得到廣泛關注和應用。
1、外形尺寸圖中尺寸“B”必須全部浸入油中免燒壞元件。被加熱油應無腐蝕性。
2、SRY3型的工作液面必須在緊固件之下,尺寸線“B”之上。
3、熔化瀝青、石蠟等固態油類時應降低電壓使用,等熔化后再升至額定電壓。以防止電量集中降低元件使用壽命。
4、發現管子表面有結碳時,必須除盡后再用,以免降低效率,甚至燒壞元件。
5、元件應存放于干燥外,若因長期放置而絕緣電阻降到低于1兆歐時,可在200℃左右的烘箱中干燥若干小時(或?qū)⒃蛪和ㄟ^(guò)數小時),即或恢復絕緣電阻。
特點:
1、大部分熱風在箱內循環,熱效率高,節約能源。
2、利用強制通風作用,箱內設有可調式分風板,物料干燥均勻。熱源可采用蒸汽、熱水、電、遠紅外,選擇廣泛。
3、整機噪音小、運轉平穩。溫度自控,安裝維修方便。
4、適用范圍廣,可干燥各種物料,是通用干燥設備。
電加熱器有很多其他燃料和設備不能實現的優勢,就是由于這些比較明顯的優勢被很多企業青睞和采用,那么外面賣的電加熱器是如何進行加熱的呢?使用方法又是怎樣的呢?
電加熱器的加熱方式有:
目前電加熱器的加熱方式主要有:電阻加熱、介質加熱、紅外性加熱、感應加熱以及電弧加熱和電子束加熱等,這些加熱方式的不同之處就是在于轉換電能的方式是不相同的。
電加熱器的使用方法:
電加熱器設備在開始啟運前要先進行檢查產品是否有漏氣的現象,接地線的裝置是否安全可靠, 確保各項工作沒有錯誤之后才可以開啟設備進行工作。
對電加熱器的電熱管應當進行絕緣檢查,它對地絕緣電阻的要求應小于1個歐姆,如果大于1個歐姆就不可以使用,一定要確保它符合標準要求后才能繼續工作。
產品的接線正確安裝好以后,接線端必須要做好密封工作,防止被氧化。
1. JB/T2379-93 《金屬管狀電熱元件》
2. GB/T19835-2005 《自限溫伴熱帶》
3. GB10067.1-88 《電熱設備基本技術條件通用部分》
4. GB5959.1 《電熱設備的安全通用部分》第一部分 通用要求
5. GB5959.2-1998 電熱設備的安全 第二部分 對電弧爐設備的特殊要求
6. GB5959.3-88 電熱設備的安全 第三部分 對感應和導電加熱設備以及感應熔煉設備的特殊要求
7. GB/T 10066.1-88 電熱設備試驗方法 通用部分
8. GB3836.1-2000 《爆炸性氣體環境用電氣設備》
循環式電加熱器相關知識
電加熱器的任務原理:
電加熱器是一種耗費電能轉換為熱能,來對需加熱物料停止加熱。在任務中高溫流體介質經過管道在壓力作用下進入其輸出口,沿著電加熱容器外部特定換熱流道,運用流體熱力學原理設計的途徑,帶走電熱元件任務中所發生的低溫?zé)崮芰?,使被加熱介質溫度降低,電加熱器出口失掉工藝要求的低溫介質。
下面萬森電器設備為大家介紹下電加熱器的8個功用特點:
1、體積小、功率大:加熱器次要采用集束式管狀電熱元件。
2、熱呼應快、控溫精度高,綜合熱效率高。
3、加熱溫度高:加熱器設計zui高任務溫度可達850℃。
4、介質出口溫度平均,控溫精度高。
5、使用范圍廣、順應性強: 該加熱器可適用于防爆或普通場所,防爆等級可達dⅡB級和C級,耐壓可達20MPa。
6、壽命長、牢靠性高:該加熱器采用特殊電熱資料制造,設計外表功率負荷低,并采用多重維護,使電加熱器平安性和壽命大大添加。
7、可全自動化控制: 依據要求經過加熱器電路設計,可方便完成出口溫度、流量、壓力等參數自動控制,并可與機算機聯網。
8、節能效果明顯,電能發生的熱量簡直99.99%傳給加熱介質。
以上就是浙江萬森電熱設備股份有限公司給大家介紹的相關內容,希望對大家有所幫助。
Task principle of electric heater:
Electric heater is a kind of energy consumption converted into heat energy to stop heating materials to be heated. In the task, the high-temperature fluid medium enters its output port under the pressure of the pipeline, along the specific heat exchange channel outside the electric heating vessel, and takes away the low-temperature heat energy occurred in the task of the electric heating element by using the method designed by the principle of fluid thermodynamics, so as to reduce the temperature of the heated medium and lose the low-temperature medium required by the process at the outlet of the electric heater.
The following Wansen electrical equipment introduces 8 functional features of the electric heater:
1. Small volume and large power: the heater mainly adopts bundle type tubular electric heating element.
2、 It has the advantages of fast thermal response, high precision of temperature control and high comprehensive thermal efficiency.
3. High heating temperature: high task temperature of heater design Zui can reach 850 ℃.
4. The medium outlet temperature is average and the temperature control accuracy is high.
5. Wide range of application and strong compliance: the heater can be used in explosion-proof or ordinary places, with explosion-proof grade up to D Ⅱ B and C, and pressure resistance up to 20MPa.
6. Long service life and high reliability: the heater is made of special electric heating materials, designed with low external power load and multiple maintenance, which greatly increases the safety and service life of the electric heater.
7. Fully automatic control: through the heater circuit design according to the requirements, it is convenient to complete the automatic control of outlet temperature, flow, pressure and other parameters, and can be networked with computer.
8. The energy-saving effect is obvious. 99.99% of the heat generated by electric energy is transmitted to the heating medium.
The above is what Zhejiang Wansen Electrical Equipment Co., Ltd. introduced to you, hoping to help you.
電加熱器是一種國際流行的、高品質長壽命電加熱設備。用于對流動的液態、氣態介質升溫、保溫、加熱。當加熱介質在壓力作用下通過電加熱器加熱腔,采用流體熱力學原理均勻地帶走電熱元件工作中所產生的巨大熱量,使被加熱介質溫度達到用戶工藝要求。
浙江萬森電熱設備股份有限公司是一家專業生產各類電加熱器,溫控設備,電站輔機的企業,有20年生產經驗,經受了市場的考驗,是全國相關產品的龍頭企業,擁有國際先進的生產技術和檢測設備。
公司以“誠信、創新、領先、雙贏”為方針,一直堅持以引進技術,集成創新,自主研究,合作開發的發展戰略,先后榮獲多項榮譽。公司在行業中較早的通過ISO9002質量體系認證。
為了獲得準確的電加熱器價格,我們可以從更為正規的電加熱器供應商報價行情獲得相關的信息,而且在可靠性上也會更好。需要根據實際情況入手,獲得的品質感也會更優,這些都是值得我們?nèi)ジ嚓P(guān)注的一環,而且在優勢上也會更突出。
根據防爆電加熱器標準,選購電加熱器時,必須要從更合理的角度入手,最終尋求的可靠性也會更突出,這樣可以確保產品擁有更好的保障,而且在優勢上有更突出的表現,這些都是值得我們?nèi)ジ嚓P(guān)注的環節,而且在優勢上更突出。
萬森電熱提供的電加熱器報價合理,也是業內性?xún)r(jià)比高的電加熱器銷售企業之一,而且在選擇性上也會更多,所以說如何更好選擇需要根據實際情況入手,而且在可靠性上也會更突出,在可靠性上更好一些,優勢更為突出。